Single Win2003 DHCP server addressing to several Vlans. ... 1004 fdnet 101004 1500 - - - ieee - 0 0 ... please read our TechRepublic Forums FAQ.
Single Win2003 DHCP server addressing to several Vlans. ... 1004 fdnet 101004 1500 - - - ieee - 0 0 ... please read our TechRepublic Forums FAQ.
Ok I have two vlans - Vlan 1 default and Vlan 5 Service. I know that on my switches I need to add a IP address helper of the DHCP so the systems can get to DHCP.
ip routing ip udp-bcast-forward timesync sntp sntp unicast snmp-server community "public" Unrestricted vlan 1 name "Default PC 0" untagged 1-12,14-26 ip address 192.168.0.8 255.255.255.0 tagged 13 ...
ip address 192.168.10.1 255.255.254.0 ip helper-address 192.168.1.1 There is only 1 port (#22) in VLAN10 so far. I put the access line on the port (22) and I put the ip helper-address on VLAN10 as ...
1.No need to install any other devise, just configure 2 vlans in the switch-Vlan2 & Vlan 3. 2.Create two dhcp pools in the cisco switch with 2 different subnets as per your requirement.
3) I kept my PC's addressing the same, but changed its gateway to VLAN1 as 192.168.1.7 (previously it was our router 192.168.1.15), and the PC can now ping the Laptop and the Laptop can ping the PC.
192.168.1.15 The 3560 is 192.168.1.7 Hmm....so I need to use 802.1Q trunking on a Routed Port on the 3560, right? And then I need to divide the "Routed Port" into multiple subinterfaces, right?
Kentrox Router = 192.168.1.15 Here is my configuration thus far: version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption! hostname ...
in our college we having the dhcp&dns in a single server, and also for internet connection we are using BSNL broadBand line it was pl...
I'm going to walk through the process of setting up DHCP on Ubuntu Server 18.04. The process is quite simple, so it shouldn't take much time at all (about five minutes).
#Default is first interface, port 6789. #You can ... HTTPServer=192.168.55.1:6789. #Also to limit the ... #If you want to send option 43 back to client for. #ranges in ...
Hello, I need to have 1 DHCP server dole out 3 different Ip address subnets. Say 192.168.100.x 192.168.101.x 192.168.1...
Scope 2 IP range is 192.168.1.100 to 192.168.1.150 In reseravtion i have given my device B mac addres and Static ip as 192.168.1.108. From my device i try to get the IP address. results are as follows
Hi gechurch, Thank you for your reply. The modem will be the interface between the server and the Internet. When I set the modem into modem only mode it gets an IP of 192.168.100.1
Create a new discussion. If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and any other specifics related to the problem.
Create a new discussion. If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and any other specifics related to the problem.
Server 2003 DHCP within a router. ... The router uses addresses between 192.168.1.64-254. That leaves 192.168.1.2-60 for me to mess with. ... or do you simply want machines that get an IP address ...
Go into your router config, usually 192.168.1.2 or 198.168.2.1 (I can't remember) and there usually is no username and password should be "admin" with no quotes.
dunno if you're still having this issue, but here's my $.02. your gateway address (the router's IP) is on one subnet (10.10.0.5) and the dhcp server is granting IP address leases on a 10.10.100.0 ...
I usually use something in 192.168.240.x to 192.168.249.0 for the local segement Planning to change at some point (just not ready for the pain that I had with another client and hard coded IP's ...