in our college we having the dhcp&dns in a single server, and also for internet connection we are using BSNL broadBand line it was pl...
in our college we having the dhcp&dns in a single server, and also for internet connection we are using BSNL broadBand line it was pl...
Many administrators forget—or don't even realize—that they can configure Dynamic Host Configuration Protocol (DHCP) on Cisco IOS routers and switches. David Davis discusses the pros and cons ...
Configuring DHCP on 2950 CISCO Switch with 2 VLANS. ... You can use your existing Switch. ... If you're new to the TechRepublic Forums, ...
Hi gechurch, Thank you for your reply. The modem will be the interface between the server and the Internet. When I set the modem into modem only mode it gets an IP of 192.168.100.1
Hello, I need to have 1 DHCP server dole out 3 different Ip address subnets. Say 192.168.100.x 192.168.101.x 192.168.1...
Create a new discussion. If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and any other specifics related to the problem.
Scope 2 IP range is 192.168.1.100 to 192.168.1.150 In reseravtion i have given my device B mac addres and Static ip as 192.168.1.108. From my device i try to get the IP address. results are as follows
Server 2003 DHCP within a router. ... The router uses addresses between 192.168.1.64-254. That leaves 192.168.1.2-60 for me to mess with. ... or do you simply want machines that get an IP address ...
Create a new discussion. If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and any other specifics related to the problem.
dunno if you're still having this issue, but here's my $.02. your gateway address (the router's IP) is on one subnet (10.10.0.5) and the dhcp server is granting IP address leases on a 10.10.100.0 ...
1.No need to install any other devise, just configure 2 vlans in the switch-Vlan2 & Vlan 3. 2.Create two dhcp pools in the cisco switch with 2 different subnets as per your requirement.
#Default is first interface, port 6789. #You can ... HTTPServer=192.168.55.1:6789. #Also to limit the ... #If you want to send option 43 back to client for. #ranges in ...
Go into your router config, usually 192.168.1.2 or 198.168.2.1 (I can't remember) and there usually is no username and password should be "admin" with no quotes.
Single Win2003 DHCP server addressing to several Vlans. ... 1004 fdnet 101004 1500 - - - ieee - 0 0 ... please read our TechRepublic Forums FAQ.
I usually use something in 192.168.240.x to 192.168.249.0 for the local segement Planning to change at some point (just not ready for the pain that I had with another client and hard coded IP's ...
I'm going to walk through the process of setting up DHCP on Ubuntu Server 18.04. The process is quite simple, so it shouldn't take much time at all (about five minutes).
After having to sort out the ealier problems with DHCp, its now working, except for the allocation of the default gateway. There is n...
I am working at a branch office and have been tasked with changing out the DHCP scope to match the overall corporate IP address scheme. The main office assigned me an IP address range of 192.168.0 ...
Well, The points keep going up so I am bound to get the right answer soon. this is the problemAfter having to sort out the ealier prob...
hi can you guide me now to do in revised setup In-short Issue of 192.168.100.1 to 192.168.100.254 Scope Range it's Assigned to pc + servers & some of static device.