C 192.168.225.0/24 is directly connected, FastEthernet0/0.225 ... by mcooper · 9 years ago In reply to VLANs and routing trouble. Thanks to everyone for replying to my problem so quickly! ...
C 192.168.225.0/24 is directly connected, FastEthernet0/0.225 ... by mcooper · 9 years ago In reply to VLANs and routing trouble. Thanks to everyone for replying to my problem so quickly! ...
by TobiF · 9 years ago In reply to VLANs and routing trouble. The subnet mask tells each host (computer) on an IP network, what addresses should be directly available. ... 192.168.225.X 255.255 ...
3) I kept my PC's addressing the same, but changed its gateway to VLAN1 as 192.168.1.7 (previously it was our router 192.168.1.15), and the PC can now ping the Laptop and the Laptop can ping the PC.
192.168.1.15 The 3560 is 192.168.1.7 Hmm....so I need to use 802.1Q trunking on a Routed Port on the 3560, right? And then I need to divide the "Routed Port" into multiple subinterfaces, right?
Kentrox Router = 192.168.1.15 Here is my configuration thus far: version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption! hostname ...
HSRP stands for Hot Standby Router Protocol, and what it does is create a virtual IP address (which hosts will use as the gateway address). This virtual address is free to move between configured ...
Here is the issue...We have a network with 5 vlans , and 15 endpoint switches (2950s). In two areas of the network, a port has been desig...
ip routing ip udp-bcast-forward timesync sntp sntp unicast snmp-server community "public" Unrestricted vlan 1 name "Default PC 0" untagged 1-12,14-26 ip address 192.168.0.8 255.255.255.0 tagged 13 ...
Ok I have two vlans - Vlan 1 default and Vlan 5 Service. I know that on my switches I need to add a IP address helper of the DHCP so the systems can get to DHCP.
You can put users who are "bandwidth hogs" (that is, their jobs require constant use of the network to interact with a particular server) on the same VLAN segment with the servers to which they ...
ip address 192.168.10.1 255.255.254.0 ip helper-address 192.168.1.1 There is only 1 port (#22) in VLAN10 so far. I put the access line on the port (22) and I put the ip helper-address on VLAN10 as ...
You would need to configure the physical cable on the physical switch as a VLAN Trunk Protocol (VTP) port; this is the opposite of the standard cabling that may usually go with a server to the ...
Create a new discussion. If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and any other specifics related to the problem.
I have several SOHO routers on my network. (Linksys and D-Link). I get five static WAN IPs from my DSL provider and I have segregated m...
To thoroughly understand routing, you need to understand routing tables. In this Daily Feature, Deb Shinder explains how routing tables are used, the information they contain, and how to view and ...
The users are not part of any local network that the exchange servers are on. Email comes into my mail server to their mailbox with an address of [email protected] and is forwarded to a custom ...
· 192.168.10.65: The next hop router used to get to subnet 32; The routing table for the 2500B router now knows how to get to subnet 32 and packets can be sent from HostA to HostB and back again. ...
However, in this case, 192.168.10.1 knows nothing about the 10.0.0.0 network, so your packets would get lost because 192.168.10.1 has no idea where to send the packets and will attempt to send ...
hello, 1 - could y tell me how i create routing between 4 VLAN on HP Procurve 3500yl : VLAN ID 100 - VoIP: 192.168.101.0/24 VLAN ID 10...
trouble with AT&T olam page ... Follow this discussion and email me when there are updates Stop following this discussion. Reply to: trouble with AT&T olam page. PLEASE NOTE: Do not post ...