Having problems configuring my D Link DI-524 router. ... I have a TATA Indicom Broadband Internet connection. ... (basically a wire comes into my house that I connect to my laptop and login ...
Having problems configuring my D Link DI-524 router. ... I have a TATA Indicom Broadband Internet connection. ... (basically a wire comes into my house that I connect to my laptop and login ...
What has me so puzzled is the variability of the problems and how it will work fine for a while and then not at all seemingly out of the blue! At this very moment, the internal antenna that came ...
PIX version 6.2 I need to allow the following ports: TCP 1720 TCP & UDP 3230-3237 From 130.63.63.11 and 130.63.63.115 to an internal host with an address of 192.168.1.150.
The IP address you assign it should be in the same subnet as the router (i.e. if your router is 192.168.2.1, your IP needs to be 192.168.2.2 through 254 assuming a subnet mask of 255.255.255.0).
Hi there! I'm pretty tired and falling asleep for the night but I noticed your question and I worked on your exact model router for a client just a few hours ago so I'll see what I can do for you.
Help with configuring router and modem for http access to nas. ... My external IP is linked via dlinkddns (which is affiliated with dyndns). ... If you're new to the TechRepublic Forums, ...
The most common approach is to place the VPN server behind the firewall, either on the corporate LAN or as part of the network’s “demilitarized zone” (DMZ) of servers connected to the Internet.
Configuring Solaris as a dial-up server. ... This page has a wiring diagram, ... The login sequence will be a typical UNIX login, with a prompt for the username and password. ...
How to configure a Cisco Unified Border Element with a Vitelity SIP Trunk to Be used by Cisco Unified Communications Manager 7 as a way out to the PSTN.
I followed exactly what you recommended, I have setup External NIC with IP assigned by the router 192.168.1.5 and Used Router IP as a GW, then I setup the LAN NIC with IP Address 192.168.2.11 and ...
The SonicWALL UI seems to work better that way. At the top right, I clicked Wizards and followed the Setup Wizard as follows: a. Change the admin password to our normal one. b. Check/set the time ...
· 192.168.10.65: The next hop router used to get to subnet 32; The routing table for the 2500B router now knows how to get to subnet 32 and packets can be sent from HostA to HostB and back again. ...
You would need to configure the physical cable on the physical switch as a VLAN Trunk Protocol (VTP) port; this is the opposite of the standard cabling that may usually go with a server to the ...
What are you looking for? GO. IT Policy Downloads 5G Developer
The Cisco Catalyst 1900 switch is a very useful tool for small workgroups or access closets needing switched 10-Mbps ports. In this Daily Feature, Todd Lammle shows you how they are configured.
Configuring IPSec on Windows 2000 Professional ... HMP, ICMP, RAW, RDP, RVD, TCP, UDP, XNS-IDP, or that it will apply to any protocol. ... Configuring IPSec on Windows 2000 Professional
Configuring DHCP on 2950 CISCO Switch with 2 VLANS. ... You can use your existing Switch. ... If you're new to the TechRepublic Forums, ...
Wireless networks can be very convenient for businesses as they eliminate reliance on Ethernet cabling. Using Active Directory and Group Policy to configure and support Wireless in the enterprise ...
I am installing a Linux Mandrake 6.5 server and cannot get the machine to use the NIC card. I have tried an NE2000 compatiable and 3Com ...
A faded print image is normally the result of one of three conditions: The printer is getting low on toner, the print density is set too low, or Economode printing is turned on. For the last two ...