RagingAura: No filters or restrictions, I admin the router. And I have reset the router to factory defaults a couple of times. The IP address of the website I can't access is 64.235.233.38 and ...
RagingAura: No filters or restrictions, I admin the router. And I have reset the router to factory defaults a couple of times. The IP address of the website I can't access is 64.235.233.38 and ...
My husband's laptop, from home, with IE and Chrome also, can't access it either. I can use his laptop when we're at scouts to access the site (different internet connection), so it's not the ...
www.barnesandnoble.com works from here.. So, try this to reset your modem/router. Turn off ALL computers on your home network, then UNPLUG/Turn OFF the router for Comcast, then turn OFF your modem ...
I'm using a D-Link DIR-825 and trying to block access to certain websites from one computer on the network. The computer is a laptop and does not have a designated IP so I was trying to use the ...
Let's say the offending IP address you want to block is 192.168.1.162. We're going to block this using UFW, with a single command: ... 192.168.1.103 Two simple methods. There you have it. Two very ...
I did the "ping" thing for cnet and xtremetop100, i don't know what this means but, the result for Cnet was ...4 packets sent and 4 received. (0%loss).(this one is okay i guess).
Have a wireless IP Wireless Camera (EasyN FS-613B). Trying to access it through a DLink DIR-615 router. Used the included setup software to identify the cam after following the setup procedure by ...
Trying for D-Link device (192.168.0.1), if not connecting to a website on the Internet. check your computer must be on the same IP sub-net to connect to the web-based utility.
Hello ! I cannot access the router (DI-524) setup menu in any way. The router works fine - the desktop computer connected via cable and the wireless internet have no problems.
First turn off (Unplug the D-Link ethernet cable attached to Iball router) the D-Link router then login to Iball modem with IP 192.168.1.1. Then go to LAN setting of Iball router and change the IP ...
I have a Netgear R7000V2 router as my primary router. I have connected a second router flashed with Tomato which servers as my secondary router. One of the LA...
Cant access router after factory reset. ... But I cant access the internet, and I cant access the router page. I've tried ipconfig with no luck. I can't even ping the damn thing!
I have a special password that's NOT in the dictionary and it would take quite a while to crack. It's just as good as my WPA password. If they can find my WPA password, then they can find my WPA ...
I have a linkys wireless g/b router and have a few problems with it that just popped up. Only 2 of the 4 ethernet hookups are working and the wireless radio has...
Number two, if you want to add a device to this router here, you would have to give an IP within this range. 192.168.1.2 all the way to 192.168.1.253. Why? That's how networking works. Now, in ...
Can't see WiFi access point from router. by ParadigmOmega May 11, 2013 11:16AM PDT. I have a ZyXel WAP3205 connected to my TP-Link TL-R600VPN router. The WiFi works just fine, but it cannot be ...
For example, if Router A's IP is 192.168.1.1, you can make the IP of Router B 192.168.1.2 (make sure that you haven't manually assigned this IP to any other device, and if you have, choose a ...
I can't access the Web setup page for my Linksys wireless B router, model BEFW11S4. Browsing to the default IP address, 192.168.1.1, results in a page not found.
I have forgotten the password and connection details and have no idea how to find them. It is a Linksys Wireless G router; I have tried contacting my provider but this has not been of any use.
Hi folks, WEB--DSL Router--DI524- PC's I have a DI524 W-AP connected to a DSL Router on my LAN using DHCP. I also enabled DHCP on the W-AP. Now I can't connect to the Router via WEBconfig(192.168 ...